Wj Flat Cage Needle Roller Bearing ANSI ABMA 18.2 Standards

WJ series needle roller and cage assemblies

RADIAL NEEDLE ROLLER AND CAGE ASSEMBLIES

REFERENCE STANDARDS:

• ANSI/ABMA 18.2 – needle roller bearings – radial, inch design.

Before selecting specifi c inch series radial needle roller and cage assemblies, the engineering section should be reviewed.

There are two primary constructions of inch series needle roller and cage assemblies. WJ assemblies are heavy-duty compared to WJC assemblies due to the nature of the roller diameter.

CONSTRUCTION

Radial needle roller and cage assemblies have a steel cage that provides both inward and outward retention for the needle rollers. The designs provide maximum cage strength consistent with the inherent high load-ratings of needle roller bearings.

Accurate guidance of the needle rollers by the cage bars allows for operation at high speeds. Needle roller and cage assemblies have either one or two rows of needle rollers.

Also available (by request) are needle roller and cage assemblies using molded, one-piece glass-reinforced engineered polymer cages. These operate well at temperatures up to 250° F (120° C) over extended periods. However, care should be exercised when bearings are lubricated with oils containing additives, as service life may be reduced if the operating temperature exceeds 212° F (100˚ C). At such high temperatures, oil can deteriorate with time and it is suggested that oil change intervals are observed.

Needle rollers with relieved ends – used in these assemblies are made of high carbon chrome steel through-hardened, ground and lapped to close tolerances for diameter and roundness. See the engineering section for further discussion of relieved end rollers.

DIMENSIONAL ACCURACY

The nominal inch assemblies, WJ and WJC, contain needle rollers manufactured to only one diameter grade. Within any one assembly, the needle rollers have a total diameter tolerance of 0.0001 in. (0.003 mm).

The limit to precision of the radial clearance of mounted needle roller and cage assemblies is the capability of the user to hold close tolerances on the inner and outer raceways.

The tolerance of the overall width of these assemblies is given in the bearing tables of this section.

MOUNTING DIMENSIONS

The needle roller and cage assembly normally uses the shaft and housing as the inner and outer raceways. To realize full bearing load rating and life, the shaft and housing must have the correct geometric and metallurgical characteristics.

The tables of dimensions for these assemblies list the suggested diameters for the shaft when used as the inner raceway. These are consistent with ISO h5 shaft raceway tolerances. Additional design details for shafts used as inner raceways can be found in the engineering section.

Since the housing normally serves as the outer raceway, it should be of suffi cient cross section to maintain adequate roundness and running clearance under load. The tables of dimensions also list the suggested diameters for the housings when used as outer raceways. These are consistent with ISO G6 housing bore tolerances. Additional design details for housings used as outer raceways can be found in the engineering section.

The suggested mounting diameter tolerances for these needle roller and cage assemblies will provide correct running clearance for most applications.

The needle roller and cage assembly must be axially located by shoulders or other suitable means. End locating surfaces should be hardened to minimize wear. For satisfactory operation, minimum axial clearance should be 0.008 in. (0.203 mm). When using type WJ assembly, fi llets adjacent to the assembly must not exceed 0.03 in. (0.762 mm) radius. When it is necessary to use fillets adjacent to WJC assembly, please consult your representative for suggestions.

Fig. B-5 . Types of inch series radial needle roller and cage assemblies

• FAQ:

•  

  1. What is your the payment condition?

  For regular products,No advance payment is needed, you can make 100% payment before shipment accordingly.

  For customized products,our payment term normally is 30% of advance, the balance 70% against copy of BOL.

  For our long term customers,you can pay 1 month after receiving the good.

   

  2. What is your sales turnover?

  Our whole year sales turnover in 2023 to 2024 is 11 million dollars

   

  3. Do you have any certifications?

  Yes, We are an IATF16949 certified needle bearings manufacturer since 2011.

   

• 4.What about the lead time?

• Our production period is 30-45 days

   

• 5.What is your production capacity?

• We are able to produce over 100 million pieces of bearings per year with different sizes and types

•  

• About us:

• ChangzhouZhihua Bearings Co.,Ltd. is an ISO9001 & TS16949 certified company which specializes in manufacturing high quality drawn up needle roller bearings, cylindricial roller bearings and Related Components. We registered our own Trade Mark "CZH" in 2011.

   

  Founded in 2004, CZH has grown to be one of the leading Manufacturer of Needle Roller Bearings, Cylindrical Roller Bearings. CZH is capable of Manufacturing both standard and custom bearings, we are dedicating to provide high quality products with competitive price since establishment. With the support of it's Engineering Department CZH is able to offer solutions and new projects which well suit the different requirements.

   

  CZH's Know-how, Innovation, Solution and the most up-to-date production system are making CZH expand and develop constantly.

   

  Our products are competitive worldwide.

   

  Allow us an opportunity to use our expertise to meet your bearing needs.